Sneaky's random builds log

Building, Modding, Setup and Repair
User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 19 Feb 2018, 16:29

narcdor wrote:
19 Feb 2018, 15:31
You'd still need a new bridge to go multi scale, but the Delano 4 (I assume) should work still. I'd be very interested to see a four string A-C at that scale, I also think an E-G would kick certain kinds of butt too.
I was looking at the ABM individual saddles with the hipshot head piece. That’s what I used with the my 7 string guitar.

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 27 Feb 2018, 17:18

Working on some truss rod templates. Plan is to buy some Perspex and make some clear routing templates for each of the different type of truss rods to make it easier.

Took three try’s to get it where I was happy with the fit and to add the flare for the wheel


Image

ImageImage


Sent from my iPhone using Tapatalk

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 28 Feb 2018, 17:56

Actual bass building !!!!

This is the bit I love shaping and testing the feel against your body. Rinse and repeat until it fits comfortably.

The routing close to final thickness ... this is the what did I do and is it recoverable.
Image

Starting to soften the side ... still panicked

Image

Deciding I’m going to keep some thickness for a small control cavity

Image

Marking with a pencil and sanding high spots

Image

This was taking ages so I used a grinder with a flap disk to do the worst of it. Can’t tell you how careful you need to be and I also used a finishing sander with 40grit. I went between the radius sanding block and finishing sander until I was done or at least 90%

Image

The cavity does get softened
Image

Arm bevel
Image

This is going to seem weird but when I held it to my body I realised it’s always on an angle so you have just the edge against your leg. So it’s a leg bevel so you have full body width when your sitting
Image
Image

Back of the body is almost done. It will be refined

Image

Image

Image


Sent from my iPhone using Tapatalk

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 28 Feb 2018, 17:59

Out of interest that’s about 2 1/2 hours worth of work. Last time I did this only with the radius sanding block that was over 10 hrs

Top will probably get done on the weekend

User avatar
Classic5
Posts: 3782
Joined: 15 Oct 2009, 19:33
Location: Melbourne

Re: Sneaky's random builds log

Post by Classic5 » 28 Feb 2018, 18:33

Love the contour work you do Pete. It's something I'd like to try one day.

2.5 hrs vs 10......that's a huge difference :notworthy:
IB-Classic#001, Xotic XJ-1T 5,Yamaha BB1024X
Glockenklang Blue Soul, Glockenklang Double, TecAmp Puma 112 Combo
"Money will buy a fine dog but only kindness will make him wag his tail"

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 28 Feb 2018, 18:49

Classic5 wrote:
28 Feb 2018, 18:33
Love the contour work you do Pete. It's something I'd like to try one day.

2.5 hrs vs 10......that's a huge difference :notworthy:
Time and patience.... you’ve definitely got the second one squared away. Should knock up a body out of pine or something cheap and easy to work with to practice on.

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 10 Mar 2018, 17:57

Finally got to the front carving and blending into the back

Image

Image

Image

Image

Image


Image

Image

Image

Image

Image

Image

Image

Image

User avatar
Classic5
Posts: 3782
Joined: 15 Oct 2009, 19:33
Location: Melbourne

Re: Sneaky's random builds log

Post by Classic5 » 10 Mar 2018, 21:08

Love the colour variation of the wood Pete. It reminds me a bit of my old Warwick.....it's gonna look fantastic :thumbup:
IB-Classic#001, Xotic XJ-1T 5,Yamaha BB1024X
Glockenklang Blue Soul, Glockenklang Double, TecAmp Puma 112 Combo
"Money will buy a fine dog but only kindness will make him wag his tail"

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 16 May 2018, 21:29

There comes a point where you have to be realistic about your capabilities for whatever the reason or limitations

Been thinking about this a lot lately as my current physical limitations mean I’m screwing up more stuff than getting right.

I love playing but I’ve had to pretty much give that up and I’m hugely frustrated at not being able to build to a quality I’m happy with so I don’t really see any options in the short term.

I’m trying to get through my current builds best I can and then I’m calling it done.

Maybe I’ll try again next year after my surgery but I’m told the damage is done so I’m not to expect improvement. Crossing my fingers

On the plus side I can take up Irish dancing ... don’t need my hand for that :lol:

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 16 May 2018, 21:33

This isn’t “woe is me” I’m just expressing my frustration

basshack
Posts: 4517
Joined: 06 Feb 2010, 10:14
Location: Melbourne Victoria

Re: Sneaky's random builds log

Post by basshack » 16 May 2018, 22:07

You can only do what you can do. Putting stuff aside till later isn’t a bad thing. You’ve got lots of mates here thinking of you and wishing for a speedy recovery.
><((((º> ·.¸¸.·´¯`·.¸.·´¯`·... ><((((º>
.·´¯`·.¸.·´¯`·... >((((º>

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 16 May 2018, 22:35

basshack wrote:
16 May 2018, 22:07
You can only do what you can do. Putting stuff aside till later isn’t a bad thing. You’ve got lots of mates here thinking of you and wishing for a speedy recovery.
Thanks, things will work out as they tend to do.

Been thinking about this for a while and it came to a head for me tonight when I did some dry runs routing a truss rod channel on some scrap ... after the fourth attempt I thought this is ridiculous. Hence the post

basshack
Posts: 4517
Joined: 06 Feb 2010, 10:14
Location: Melbourne Victoria

Re: Sneaky's random builds log

Post by basshack » 17 May 2018, 09:41

You could always take my approach and don't use one....
><((((º> ·.¸¸.·´¯`·.¸.·´¯`·... ><((((º>
.·´¯`·.¸.·´¯`·... >((((º>

User avatar
drbass
Posts: 3062
Joined: 04 Apr 2013, 05:31
Location: Doreen, Victoria
Contact:

Re: Sneaky's random builds log

Post by drbass » 17 May 2018, 12:32

Hi Pete,

You’re not getting away that easily. First of all sorry to hear that things got worse rather than improve. But that’s not enough reason to throw out the baby with the bath water. Rest up, get the surgery done, and then see where you’re at.

The lutherie forum definitely needs you - the more quirky out-of-the-box threads the better, and you always have great comments and suggestions.

Hang in there!

Regards,
Michael
- Merlin “Kermit” 6 multi, Merlin Gaia 6 fretless, Merlin Rockmachine 5, Merlin NT5, Manta 5, Manta 5 YOLO, ("Red Baron" 5), Q 5, (Sandberg Classic S2-5), (Thumb-4)
- Genzler Magellan 800, 2 Genzler BA12-3

User avatar
SneakyJak
Posts: 1556
Joined: 03 Sep 2011, 22:15
Location: Canberra

Re: Sneaky's random builds log

Post by SneakyJak » 17 May 2018, 18:14

drbass wrote:
17 May 2018, 12:32
Hi Pete,

You’re not getting away that easily. First of all sorry to hear that things got worse rather than improve. But that’s not enough reason to throw out the baby with the bath water. Rest up, get the surgery done, and then see where you’re at.

The lutherie forum definitely needs you - the more quirky out-of-the-box threads the better, and you always have great comments and suggestions.

Hang in there!

Regards,
Michael
I’ll linger around for sure I enjoy watching the builds come together about as much as I do building my own.

Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests