Future Builds - Kinda Not Random

Building, Modding, Setup and Repair
basshack
Posts: 4323
Joined: 06 Feb 2010, 10:14
Location: Melbourne Victoria

Re: Future Builds - Kinda Not Random

Post by basshack » 14 May 2018, 11:40

drbass wrote:
14 May 2018, 11:19
basshack wrote:
13 May 2018, 21:57
I'm not looking....
And yet here you are, Blaine ... ;)

Regards,
Michael
And yes I need to find a nice top for the new build.
><((((º> ·.¸¸.·´¯`·.¸.·´¯`·... ><((((º>
.·´¯`·.¸.·´¯`·... >((((º>

User avatar
drbass
Posts: 2851
Joined: 04 Apr 2013, 05:31
Location: Doreen, Victoria
Contact:

Re: Future Builds - Kinda Not Random

Post by drbass » 14 May 2018, 20:31

Can't think of too many other things representing so much money in such small packages - printer ink, maybe? But (at least in my opinion) worth every cent: Delano pickups.



Regards,
Michael
- Kermit 6 multi, Kermit Gaia 6 fretless, Kermit Rockmachine 5, Manta 5, Manta 5 YOLO, ("Red Baron" 5), Q 5, (Sandberg Classic S2-5), (Thumb-4)
- Genzler Magellan 800, 2 Genzler BA12-3
- EBS OctaBass, Boss MS-3, Line6 G50

User avatar
Classic5
Posts: 3645
Joined: 15 Oct 2009, 19:33
Location: Melbourne

Re: Future Builds - Kinda Not Random

Post by Classic5 » 14 May 2018, 21:04

I can think of one other. A Phil Jones BigHead :p

Yep, the Delano pickups are truly wonderful. Nice selection you have there :cool:
IB-Classic#001, Xotic XJ-1T 5,Yamaha BB1024X
Glockenklang Blue Soul, Glockenklang Double, TecAmp Puma 112 Combo
"Money will buy a fine dog but only kindness will make him wag his tail"

User avatar
drbass
Posts: 2851
Joined: 04 Apr 2013, 05:31
Location: Doreen, Victoria
Contact:

Re: Future Builds - Kinda Not Random

Post by drbass » 17 May 2018, 17:08

Had a little bit of time today.

Routed the battery compartment for the Special Q" - no pic, sorry.

Catch-up from the other day: the "top sandwich" for the neck-through Kermit being glued up:


Glued up real nice with the Westsystem epoxy. Using the slow hardener (206) you get this really nice low viscosity fluid that spreads beautifully and fills any voids (and soaked into the veneer sheet - stabilisation!!).

Machined the in-body section of the neck down to 27 mm - here's where the pickups will be located (please note the walnut wings are 28 mm thick):


They're big pickups (EMG-style) sitting in the Ken Smith spots (adjusted for 35"). Correction: they're sitting in the actual spots for a 34", correct locations will be 22 (neck) and 24 (bridge) mm closer to the bridge - sorry!

And here's the glueing setup for the fretboard. Using Selley's araldite (much higher viscosity here), nice and even squeeze-out:


That'll be cured tomorrow. Can't make it to the workshop unfortunately and not sure about the weather (remember, open air workspace), plus I have gigs Fri and Sat so there mightn't be much more this week.

Regards,
Michael
- Kermit 6 multi, Kermit Gaia 6 fretless, Kermit Rockmachine 5, Manta 5, Manta 5 YOLO, ("Red Baron" 5), Q 5, (Sandberg Classic S2-5), (Thumb-4)
- Genzler Magellan 800, 2 Genzler BA12-3
- EBS OctaBass, Boss MS-3, Line6 G50

User avatar
drbass
Posts: 2851
Joined: 04 Apr 2013, 05:31
Location: Doreen, Victoria
Contact:

Re: Future Builds - Kinda Not Random

Post by drbass » 20 May 2018, 21:11

Some progress.

Neck fitted and final width for the Special Q, and I started carving as well (can't see it in the pic). Colour is way off - sorry, looks much nicer in real life.



For the neck-through Kermit the board's on and cut to length, and I've measured (several times) and marked the bits that need to go (will be sawed next week) both on the neck and the top sandwich.

That's it. There'll be a lot more happening in the next 4 - 6 weeks so stay tuned.

Regards,
Michael
- Kermit 6 multi, Kermit Gaia 6 fretless, Kermit Rockmachine 5, Manta 5, Manta 5 YOLO, ("Red Baron" 5), Q 5, (Sandberg Classic S2-5), (Thumb-4)
- Genzler Magellan 800, 2 Genzler BA12-3
- EBS OctaBass, Boss MS-3, Line6 G50

User avatar
Classic5
Posts: 3645
Joined: 15 Oct 2009, 19:33
Location: Melbourne

Re: Future Builds - Kinda Not Random

Post by Classic5 » 21 May 2018, 08:15

Looks so good Michael. What's the thickness of the top wood on this one? Just curious for future potential purchases.
IB-Classic#001, Xotic XJ-1T 5,Yamaha BB1024X
Glockenklang Blue Soul, Glockenklang Double, TecAmp Puma 112 Combo
"Money will buy a fine dog but only kindness will make him wag his tail"

User avatar
drbass
Posts: 2851
Joined: 04 Apr 2013, 05:31
Location: Doreen, Victoria
Contact:

Re: Future Builds - Kinda Not Random

Post by drbass » 21 May 2018, 08:19

Classic5 wrote:
21 May 2018, 08:15
Looks so good Michael. What's the thickness of the top wood on this one? Just curious for future potential purchases.
Thank you, Ivan,

As I said the light was dreadful, couldn't even get close to a proper white balance and colour reproduction in post-processing. It looks much (a lot) better in real life, and I can't wait to see this with the finish applied.

This particular top was just over 7 mm - I guess it'd be about 5.5 - 6 now (thicknessing, sanding).

Regards,
Michael
- Kermit 6 multi, Kermit Gaia 6 fretless, Kermit Rockmachine 5, Manta 5, Manta 5 YOLO, ("Red Baron" 5), Q 5, (Sandberg Classic S2-5), (Thumb-4)
- Genzler Magellan 800, 2 Genzler BA12-3
- EBS OctaBass, Boss MS-3, Line6 G50

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest